鸭式布局飞机矢量喷流对地面效应影响的风洞试验

针对单发鸭式布局飞机，通过低速风洞试验，研究了矢量喷流对飞机地面效应的影响特性。研究结果表明：发动机喷流使得飞机的地面效应增强，升力系数增加，降低飞机起飞/降落时的飞行速度，缩短起降距离，从而改善飞机起降性能。发动机喷管上/下偏转时，矢量喷流对飞机上下表面气流诱导不对称，均使地面效应阻力系数增量减小。在此基础上，基于数值模拟结果对喷流与地面效应的相互作用机理进行了分析。     

TEC differences for the mid-latitude ionosphere in both sides of the longitudes with zero declination

Based on measurements of ground-based GPS station network, differences of the mid-latitude ionospheric TEC in the east and west sides of North America, South America and Oceania have been analyzed in this paper. Results show that for nearly all seasons from 2001 to 2010 and in both sides of the longitudes with zero declination, there exist systematic differences for the mid-latitude ionospheric TEC in the regions mentioned above and the features of these differences markedly depend upon the local time but less depend upon seasons and the level of solar activity. Theory analysis shows that the longitude variations of both declination and zonal thermospheric winds are one of important factors to cause differences of the mid-latitude ionospheric TEC in both sides of the longitudes with zero declination.     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

全模颤振双索悬挂系统刚体模态频率研究

研究绳系结构和绳索预紧力对全模颤振双索悬挂系统刚体模态频率的影响。首先，基于绳索并联机构理论，对双索悬挂系统进行静力学建模，引入加权矩阵，推导了双索悬挂系统静刚度模型；其次，建立双索悬挂系统无阻尼振荡方程，分析双索悬挂系统刚体模态频率变化规律；进而，搭建了双索悬挂系统地面样机，开展系统模态频率测试试验，研究系统刚体模态频率的影响因素及其变化规律；最后，参考试验结果修正所建数学模型。结果表明，随着绳索预紧力的增加，系统刚体模态频率呈上升趋势，但各阶刚体模态的固有频率上升速率不同，平动模态的固有频率受绳索预紧力影响比转动模态小得多；在转动模态方面，滚转模态的固有频率最大且上升快；在平动模态方面，升沉模态的固有频率大于横侧滑模态的固有频率；双索经过的机身前后滑轮与飞机模型质心之间的相对位置变化会不同程度地影响支撑系统俯仰模态、偏航模态的固有频率，但几乎不影响其滚转模态的固有频率。研究发现，通过控制悬挂绳索预紧力的大小，合理设计机身上的滑轮安装位置，能够有效降低双索悬挂系统刚体模态频率。研究结果对于优化设计全模颤振双索悬挂系统具有指导意义。     

一种引射增强型二次喉道新方案的数值模拟

为提高大型超声速风洞的运行经济性，设计了一种通过引射低总压冷介质提高扩压性能的新型二次喉道扩压器，其结构特征是在扩压器收敛段前方增加侧壁凹槽，在凹槽前沿位置引入低总压常温空气作为冷介质，通过引射扩散作用在扩压器壁面形成气膜，调节二次喉道实际流通直径，较大程度上增强二次喉道的静压恢复能力，同时又降低二次喉道壁面热负荷，冷却壁面。数值验证结果表明，所设计新型二次喉道方案可通过调节引射气量自适应较宽范围的运行条件，有效隔离扩压器壁面直接接触高温燃气，同时提高了扩压能力，节省后段接力引射器的主动流流量近30%，对风洞运行经济性提升十分明显。     

尖侧缘机身布局的俯仰力矩特性及扰流板控制

针对尖侧缘机身布局在大迎角下存在的正俯仰力矩（抬头力矩）问题，通过风洞试验，首先研究了俯仰力矩的迎角分区特性及流动演化规律：线性增长区（迎角为0°~15°），俯仰力矩线性增加，全机从附着流到形成进气道前缘涡和机翼涡；非线性增长区（迎角为17.5°~32.5°），俯仰力矩非线性增加，机头涡出现，机头涡和进气道前缘涡逐渐增强，机翼涡增强后破裂；衰减区（迎角为35°~65°），俯仰力矩逐渐减小，机头涡增强后破裂，进气道前缘涡破裂发展，机翼涡完全破裂。其次，发现了机身前体是产生正俯仰力矩的主要来源，机头涡是导致大迎角下正俯仰力矩的主控流动。当迎角为40°时，前体各截面正俯仰力矩在进气道前缘处达到最大，主要是由于该处机头涡诱导产生了较强的法向力。最后，提出了大迎角机身扰流板控制技术，产生了较好的控制效果。当迎角为40°时，扰流板可使正俯仰力矩减少62%，其原因是扰流板降低了机头涡涡量及其诱导产生的法向力，减少了机身前体对正俯仰力矩的贡献。该控制技术的缺点是扰流板会带来一些升力损失和附加阻力。基于尖侧缘机身参考宽度的雷诺数为2.59×10⁵。     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

全模颤振风洞试验三索悬挂系统多体动力学分析

全模颤振风洞试验需要通过软支撑系统模拟飞行器的自由飞行状态并调整模型姿态达到配平状态。参考NASA双索悬挂方案，提出了一种两电机驱动的三索悬挂系统，利用后方两索的同向/反向联动实现模型俯仰和滚转姿态的调整，利用弹簧刚度以及钢绳张力设计实现支撑频率要求。基于柔性多体动力学方法，建立了包括飞行器刚体模型、柔性索、滑轮、弹簧、气动力模型、伺服电机控制在内的复杂系统动力学模型，其中，利用任意拉格朗日-欧拉（ALE）变长度索单元描述钢绳，利用不约束物质坐标的索结点约束描述钢绳与滑轮相互作用，利用索结点物质输运速度约束描述伺服电机绞盘，利用飞行力学的气动力模型描述吹风下的气动力。基于该模型，通过小扰动响应辨识研究了弹簧刚度、钢绳张力、连接点位置等因素对支撑频率的影响规律，并分析了系统姿态调整能力，俯仰调整范围达到-12.5°~12.5°，滚转调整范围达到-45°~45°。采用滑轮处电位计测量的钢绳相对位移作为反馈信号，基于设计的控制律利用多体动力学求解器与Simulink对风洞吹风下的姿态调整过程进行仿真，模型达到配平状态，获得了吹风下的索拉力和伺服电机功率，为系统设计提供基础。     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.